hanski 40 Posted January 28, 2019 Arisen from the depths of my watch bin, an incredible and rare ghost 1680 red dial submariner - catch a glimpse before it vanishes. No papers, no history, nothing - provenience unknown. Much like the name, it’s like a apparition appearing out of nowhere. But the work was real: - Fully reshaped case including lugs, chamfers, spring bar holes, and CG’s - Case repolished and rebrushed - Aged and repolished bezel - Ghosted Insert, backside maintained as black - Relumed Dial and hand set to match with thin, lightly pillowed lume plots - Hands aged in an organic blend of apple cider vinegar and fresh pacific seawater - Reassembled with freshly lubed gaskets, all parts compression fitted Share this post Link to post Share on other sites
Robtherib 0 Posted January 28, 2019 Sent PM with intent........ Share this post Link to post Share on other sites
gabro 0 Posted January 30, 2019 Would you kindly explain more how aging hands usibg "organic blend of apple cider vinegar and fresh pacific seawater" works? Please Sent from my SM-G965F using Tapatalk Share this post Link to post Share on other sites
hanski 40 Posted January 31, 2019 2 hours ago, gabro said: Would you kindly explain more how aging hands usibg "organic blend of apple cider vinegar and fresh pacific seawater" works? Please Sent from my SM-G965F using Tapatalk Of course. Step 1: Remove lume from the hands. For this I use a sharp xacto and carefully scrap off from the back. Step 2: I stabilize the hands in a thin, flat pad of rodico, right side up. I use 1500 grit wet-dry sandpaper to buff and rough up the surface of the hands. Buff in short, multi direction movements - this avoids a directional finish. Step 3: Mix a 2:1 ratio of seawater with Apple cider vinegar (we buy mostly organic stuff so this the organic). Using tap water with lots of salt works too. Use hot or boiling water to assist in dissolving the salt in to the water. Step 4: Dunk hands in to mixture over night Step 5: Remove hands, repeated buffing/roughing but a little gentler this time. Step 6: Dunk and remove hands again. Let hands air dry. I don’t get rid of or dry off the fluid that comes with them. I left that evaporate. Step 7: Relume hands to match dial Share this post Link to post Share on other sites
onionbag 1 Posted January 31, 2019 Is this a sale or are you showing yer arse? Share this post Link to post Share on other sites
Glaude 1,615 Posted January 31, 2019 15 minutes ago, onionbag said: Is this a sale or are you showing yer arse? Share this post Link to post Share on other sites
onionbag 1 Posted January 31, 2019 (edited) 3 minutes ago, Glaude said: So, this thread is not a sale thread? Then he/she's not allowed to solicit offers. Edited January 31, 2019 by onionbag Share this post Link to post Share on other sites
Glaude 1,615 Posted January 31, 2019 Just now, onionbag said: So, this thread is not a sale thread? Nope, I believe it was to share nice picture of the build with us Share this post Link to post Share on other sites
hanski 40 Posted January 31, 2019 4 minutes ago, onionbag said: So, this thread is not a sale thread? Then he/she's not allowed to solicit offers. Hi, no, I like to share my builds and projects. Posted this to show what I did, didn’t intend to sell it straight away - didn’t solicit offers nor did I post in the sales section. Got a PM about it asking if I’d sell it. Instead of any kind of back door sale, I opted to post publically a reserved sale. If you look at my history I’ve clearly separated builds and projects from anything I sell. Share this post Link to post Share on other sites
onionbag 1 Posted January 31, 2019 9 minutes ago, Glaude said: Nope, I believe it was to share nice picture of the build with us Ok mate. You can take the hit when the buyer complains. I'm happy with that. Share this post Link to post Share on other sites
onionbag 1 Posted January 31, 2019 4 minutes ago, mzinski said: Hi, no, I like to share my builds and projects. Posted this to show what I did, didn’t intend to sell it straight away - didn’t solicit offers nor did I post in the sales section. Got a PM about it asking if I’d sell it. Instead of any kind of back door sale, I opted to post publically a reserved sale. If you look at my history I’ve clearly separated builds and projects from anything I sell. I don't give a flying fuck about your history. No offence meant mate. Share this post Link to post Share on other sites
Glaude 1,615 Posted January 31, 2019 3 minutes ago, onionbag said: You can take the hit when the buyer complains Proper sale post, nothing done wrong, no complains to be have on that part 1 minute ago, onionbag said: I don't give a flying fuck about your history. No offence meant mate. Pretty sure the same goes for your opinion about it No offence of course Share this post Link to post Share on other sites
hanski 40 Posted January 31, 2019 1 minute ago, onionbag said: I don't give a flying fuck about your history. No offence meant mate. Neat. Can we back up and clear things up? My post did not solicit anything. I posted a funny (I thought it was funny at least) narrative and specs of my build. I got a PM inquiring if it was for sale, I responded as: “First, I posted the watch in Vintage Watches to show everyone what I've been up to. I like to share my work. I was considering selling it but I'd prefer not to go the route of a backdoor sale. I think that is better for everyone - including yourself. ” I subsequently posted a public, reserved sale for him to respond to. Please let me know if there is a better way to respond to solicitations to sell my builds. Share this post Link to post Share on other sites
Glaude 1,615 Posted January 31, 2019 1 minute ago, mzinski said: Neat. Can we back up and clear things up? My post did not solicit anything. I posted a funny (I thought it was funny at least) narrative and specs of my build. I got a PM inquiring if it was for sale, I responded as: “First, I posted the watch in Vintage Watches to show everyone what I've been up to. I like to share my work. I was considering selling it but I'd prefer not to go the route of a backdoor sale. I think that is better for everyone - including yourself. ” I subsequently posted a public, reserved sale for him to respond to. Please let me know if there is a better way to respond to solicitations to sell my builds. To me you acted exactly as expected, it's always best to make a public sale, for both the history of the future re-selling of the watch on the board (so we have a price history & origin) and if anything were to go wrong, we could catch a potential bad buyer or seller. Reserved sales are often conducted like that No worries to have Share this post Link to post Share on other sites
onionbag 1 Posted January 31, 2019 There is a better way. You're not allowed to solicit for work here. Share this post Link to post Share on other sites
Glaude 1,615 Posted January 31, 2019 2 minutes ago, onionbag said: There is a better way. You're not allowed to solicit for work here. There is not. He didn't solicit any work, the work was done, he shared it, somebody was interested, he made a sale post. Multiple mods have seen those both threads, nothing was said against. Share this post Link to post Share on other sites
onionbag 1 Posted January 31, 2019 Just now, Glaude said: To me you acted exactly as expected, it's always best to make a public sale, for both the history of the future re-selling of the watch on the board (so we have a price history & origin) and if anything were to go wrong, we could catch a potential bad buyer or seller. Reserved sales are often conducted like that No worries to have That's factually incorrect. The sales rules explicitly say you may not tout for business, 1 minute ago, Glaude said: There is not. He didn't solicit any work, the work was done, he shared it, somebody was interested, he made a sale post That is touting. Share this post Link to post Share on other sites
Glaude 1,615 Posted January 31, 2019 2 minutes ago, onionbag said: That's factually incorrect. The sales rules explicitly say you may not tout for business, Good thing he didn't then And building vintages watches in the intention of selling them has never been against the rules, check them again 2 minutes ago, onionbag said: That is touting. No Share this post Link to post Share on other sites
onionbag 1 Posted January 31, 2019 (edited) 6 minutes ago, Glaude said: Good thing he didn't then Yes he did. By making this post outside his sale. This is not up for discussion...take it to the back room. As you said..."tech support"... Edited January 31, 2019 by onionbag Share this post Link to post Share on other sites
Glaude 1,615 Posted January 31, 2019 3 minutes ago, onionbag said: Yes he did. By making this post outside his sale. This is not up for discussion...take it to the back room. No, he didn't, you are free to read how the whole thing was done, again, if you can't understand it, get help. This is indeed not up for your discussion, as you are not a mod here anymore, leave that matter for those concerned, I'm personnaly not in charge of that matter, so this end my contribution to this topic Share this post Link to post Share on other sites
Luxuracer 14 Posted January 31, 2019 My 'non ghost' 1680 Red ... says hello. Share this post Link to post Share on other sites
hanski 40 Posted January 31, 2019 41 minutes ago, Luxuracer said: My 'non ghost' 1680 Red ... says hello. Nice! Do you know the history behind the red hand? I’ve seen them on a handful of builds here and there. Share this post Link to post Share on other sites
gabro 0 Posted January 31, 2019 Of course. Step 1: Remove lume from the hands. For this I use a sharp xacto and carefully scrap off from the back. Step 2: I stabilize the hands in a thin, flat pad of rodico, right side up. I use 1500 grit wet-dry sandpaper to buff and rough up the surface of the hands. Buff in short, multi direction movements - this avoids a directional finish. Step 3: Mix a 2:1 ratio of seawater with Apple cider vinegar (we buy mostly organic stuff so this the organic). Using tap water with lots of salt works too. Use hot or boiling water to assist in dissolving the salt in to the water. Step 4: Dunk hands in to mixture over night Step 5: Remove hands, repeated buffing/roughing but a little gentler this time. Step 6: Dunk and remove hands again. Let hands air dry. I don’t get rid of or dry off the fluid that comes with them. I left that evaporate. Step 7: Relume hands to match dialThanks mate Sent from my SM-G965F using Tapatalk Share this post Link to post Share on other sites
fatarms 7,777 Posted January 31, 2019 34 minutes ago, mzinski said: Nice! Do you know the history behind the red hand? I’ve seen them on a handful of builds here and there. I think the red second hand was just something to accentuate the red lettering on the dial. I sold one a while back with the same intention, just to accentuate the dial. No gens exist with a red second hand that I know of. https://www.rwg.bz/board/index.php?/topic/136631-both-sold-ice-blue-21j-rolex-daydate-1680-red Share this post Link to post Share on other sites