FreezerBurn 0 Posted February 5, 2011 Welcome to the FreezerBurn memorial.. I pulled the crown out of my IWC Big Pilot from Mary within the hour I got it ... This is the first time I've been inside of a watch. I'm ok with mechanics, but have zip experience on movements. I'm ready to learn my lesson, I just hope it's not an expensive one... Share this post Link to post Share on other sites
graman 2 Posted February 5, 2011 Mate...if you haven't snapped the stem, or buggered the mech up, then it should snap back in. Just make sure that the movement is aligned with the tube, and give it a bit of a jiggle back and forth (like you're winding it only way less) as you slide it in. Let us know how you go Share this post Link to post Share on other sites
FreezerBurn 0 Posted February 5, 2011 Mate...if you haven't snapped the stem, or buggered the mech up, then it should snap back in. Just make sure that the movement is aligned with the tube, and give it a bit of a jiggle back and forth (like you're winding it only way less) as you slide it in. Let us know how you go well it went int some of the way and was able to wind the watch, but was still loose. tried to push it in but it gave kind of a smooth push in like the bar was sinking into the crown or something like that. I could give it more force but I don't want to give it too much force. Share this post Link to post Share on other sites
narikaa 129 Posted February 5, 2011 Mate...if you haven't snapped the stem, or buggered the mech up, then it should snap back in. Just make sure that the movement is aligned with the tube, and give it a bit of a jiggle back and forth (like you're winding it only way less) as you slide it in. Let us know how you go Thats marvellous advise if youd like the guy to totally fukk his keyless works (If he hasnt already!) Dear OP you put the stem (which clearly is not snapped) back in then you need to depress the catch here: Ever so slightly to seat it all the way in Hope that that remedies the situation - There may of course have been something dramatically wrong with the keyless works (that which holds said stem in place) in the first place to allow this to happen - assuming you didnt 'Conan the Barbarian' it Failing all that you could always take one of those 'Instant Timeserved Watchsmith Tablets' that many on these fora avail themselves of . Share this post Link to post Share on other sites
prestigewatchco 2 Posted February 5, 2011 Some of these are difficult to put back in. I have had to slacken the crown off before now to get the stem far enough in . The spring loading on the crown doesn't allow the stem to go in far enough on occation . If you are not sure how to slacken the crown off then maybe better to get it done and re installed by someone you can mess up the keyless very easy if you push too hard on the lock button. Something to always remember when working on watches is the least pressure gets the best results if you have to force it you are doing it wrong This is unfortunately one of the more difficult stems to install because of the sping loaded crown Share this post Link to post Share on other sites
FreezerBurn 0 Posted February 5, 2011 WE DID IT! Didn't realize that little dot was a button. Pressed it down with my pick and it slid right in. Set the time and calendar date just fine and it's ticking away! Was sweating bullets, but just this small experience was a giant leap for me. Thanks for the support! Share this post Link to post Share on other sites
graman 2 Posted February 5, 2011 Mate...if you haven't snapped the stem, or buggered the mech up, then it should snap back in. Just make sure that the movement is aligned with the tube, and give it a bit of a jiggle back and forth (like you're winding it only way less) as you slide it in. Let us know how you go Thats marvellous advise if youd like the guy to totally fukk his keyless works (If he hasnt already!) Dear OP you put the stem (which clearly is not snapped) back in then you need to depress the catch here: Ever so slightly to seat it all the way in Hope that that remedies the situation - There may of course have been something dramatically wrong with the keyless works (that which holds said stem in place) in the first place to allow this to happen - assuming you didnt 'Conan the Barbarian' it Failing all that you could always take one of those 'Instant Timeserved Watchsmith Tablets' that many on these fora avail themselves of . Lesson learned ....forgot about the catch......Thank you my lord Share this post Link to post Share on other sites
djprone 0 Posted February 5, 2011 All this pulling out and sliding back in talk is making me horny Share this post Link to post Share on other sites
narikaa 129 Posted February 5, 2011 Why (looking at the state of your avatar) does that not surprise me . Share this post Link to post Share on other sites
graman 2 Posted February 5, 2011 With an avatar like that, I think djprone'd do a black snake with a festering asshole........ .....ok...maybe only if you held it's head... Share this post Link to post Share on other sites
ChasR 0 Posted February 13, 2011 I had this problem with my Asian 7750 Tag Calibre 16 Day Date and the stem would not click back in place Movement was working but couldn't locate the shaft even with pressing the catch Kept trying and it eventually caught, I could wind, change hour, day, date, but watch has stopped. Watch cost about $300 so unless someone is prepared to treat me as a charity and get it working again for nothing I don't think that I will be putting out $200 plus to put it on my wrist again Share this post Link to post Share on other sites