baruch 0 Posted June 21, 2011 Gents!!! I have a problem, I need to change mine ceramic bezel fof mine rolex dssd, but HOW DO I DO THAT???? I hope you can help me because I love mine watch. Greets, B Share this post Link to post Share on other sites
Member X 91 Posted June 21, 2011 Do you have the replacement bezel? If not, contact the dealer you bought the watch from - they should be able to get you a replacement bezel After that, I think there is a guide on here for changing it! B) Share this post Link to post Share on other sites
baruch 0 Posted June 21, 2011 Do you have the replacement bezel? If not, contact the dealer you bought the watch from - they should be able to get you a replacement bezel B) After that, I think there is a guide on here for changing it! :pollox: HAHAAHAH member x thankyou for replying. I only have one watch to wear yes the bezel is coming so can you help me with this? I hope you can thanks again Gr B Share this post Link to post Share on other sites
Member X 91 Posted June 21, 2011 I have not tried it myself! B) One of the modders on here should be able to help you when they see this thread Maybe mikemcnair, Brightlight, Rolexaddict... Share this post Link to post Share on other sites
Silverspeed 10 Posted June 21, 2011 Do you need the insert changed or the bezel? The DSSD bezel is very hard to remove, the insert is a lot easier to replace place a sharp and thin knife under the insert at the crystal side, and slowly cut your way under the insert. it might help to heat up the insert with a hairdryer to activate the glue. Share this post Link to post Share on other sites
tissotman 0 Posted June 21, 2011 I would like to change the bezel on my deep sea as well but where can i get the correct bezel from with correct triangle at the top and correct 10 ? Share this post Link to post Share on other sites
ThinkBachs 1 Posted June 21, 2011 It's easy! In fact, I just did one this morning. Take a towel and place your watch on top. Put some pressure on the side of the pearl and pop it off. Take a hair dyer on heat, low wind, and warm that sucker up. Don't use a heat gun, you will make your RING LOCK paint disappear! Warm the insert up good and warm, then use a nice thick safety pin through the hole where the pearl was and GENTLY pull up, warm again just to be safe, and it'll come out no problem. You'll want to pull up using the pin with the point going towards the thickest part of the insert. They're fragile and can crack easily if you try applying pressure at the top or bottom of the hole. Put the pearl back in and glue from behind only to replace it. Easy-Peasy. Share this post Link to post Share on other sites
baruch 0 Posted June 21, 2011 WOEHOEE I willd definetely pm these guys. Thankyou very much Share this post Link to post Share on other sites
baruch 0 Posted June 21, 2011 Do you need the insert changed or the bezel? The DSSD bezel is very hard to remove, the insert is a lot easier to replace place a sharp and thin knife under the insert at the crystal side, and slowly cut your way under the insert. it might help to heat up the insert with a hairdryer to activate the glue. Yes definetely the insert of the watch, thankyou very much silverspeed!!!!!!!!!! Share this post Link to post Share on other sites
baruch 0 Posted June 21, 2011 It's easy! In fact, I just did one this morning. Take a towel and place your watch on top. Put some pressure on the side of the pearl and pop it off. Take a hair dyer on heat, low wind, and warm that sucker up. Don't use a heat gun, you will make your RING LOCK paint disappear! Warm the insert up good and warm, then use a nice thick safety pin through the hole where the pearl was and GENTLY pull up, warm again just to be safe, and it'll come out no problem. You'll want to pull up using the pin with the point going towards the thickest part of the insert. They're fragile and can crack easily if you try applying pressure at the top or bottom of the hole. Put the pearl back in and glue from behind only to replace it. Easy-Peasy. Oke oke I will trye this and hope it will work :wish me good luck Share this post Link to post Share on other sites
baruch 0 Posted June 21, 2011 I would like to change the bezel on my deep sea as well but where can i get the correct bezel from with correct triangle at the top and correct 10 ? from mary, watchinternational. Share this post Link to post Share on other sites
MikeMcNair 0 Posted June 22, 2011 remove movement (easy) put in glass of HOT water for 5 min (easy) pry up insert from crystal side as others have said (easy) put on new bezel insert assuring it is lined up correct;y (easy) rejoice and drink a beer Share this post Link to post Share on other sites
Donnie 0 Posted September 7, 2011 It's easy! In fact, I just did one this morning. Take a towel and place your watch on top. Put some pressure on the side of the pearl and pop it off. Take a hair dyer on heat, low wind, and warm that sucker up. Don't use a heat gun, you will make your RING LOCK paint disappear! Warm the insert up good and warm, then use a nice thick safety pin through the hole where the pearl was and GENTLY pull up, warm again just to be safe, and it'll come out no problem. You'll want to pull up using the pin with the point going towards the thickest part of the insert. They're fragile and can crack easily if you try applying pressure at the top or bottom of the hole. Put the pearl back in and glue from behind only to replace it. Easy-Peasy. What type of glue is used for this? Share this post Link to post Share on other sites
MikeMcNair 0 Posted September 7, 2011 GS-Hypocement is what I use for ceramic bezel inserts. Share this post Link to post Share on other sites
KeNnY 29 Posted September 7, 2011 GS-Hypocement is what I use for ceramic bezel inserts. +1 Share this post Link to post Share on other sites
vexorg 0 Posted September 7, 2011 are the inserts a common size? i would like to get a couple and franken up a watch or two Share this post Link to post Share on other sites
Donnie 0 Posted September 8, 2011 GS-Hypocement is what I use for ceramic bezel inserts. Thanks! Share this post Link to post Share on other sites
Luthier 1 Posted September 8, 2011 Soldering iron works much better on ceramic inserts, that hair gun. You can apply heat on insert only. Share this post Link to post Share on other sites
MikeMcNair 0 Posted September 8, 2011 Soldering iron works much better on ceramic inserts, that hair gun. You can apply heat on insert only. Actually George, that's a good idea, but ceramic can burn if not careful. I suggest laying case in a cup of hot water for a minute or five, then pressing out the crystal, and using a razor for the bezel insert. Works well, is fast enough, and frankly, is EASY! Share this post Link to post Share on other sites