Vintagizing 47mm Egi Part 1

[Timebandit 0]

Hi Members,

I decided to age my 47mm Egi Bezel. But it came out that I vintagized the whole watch.

Here is the bezel I’ve started with. I wanted to get some contact corrosion through the contact

from stainless-steel with carbon-steel in connection with some moisture

The bezel was polished with cape cod and the bezel pearl was made with laquer and lume powder. I applicated a drop of water on each pin

 

I used a file and an old scrap Metal from carbon steel to produce some Iron powder

 

Then, I sprinkled the powder over the bezel

 

The redundant powder was blown away carefully. Only the powder around the pins was left, because of the moisture from that drop of water.

 

I placed the prepared bezel in a container with some water ( for a moist climate ) at the bottom.

 

After three hours, the bottom from the bezel started to get a little rusty

 

After one day, about 28 hours later, the bezel got a real rusty surface. Not too hard, but also not simple to remove. I rubbed with a cloth over it and it was still there.

I also removed the pearl, it needs a more aged one.

The next thing I want to age is the case. It is now in a container, treated with the same procedure.

 

Ok Guys,

busy again yesterday. I took the case the day before yesterday in a can, together with rusty screws and some other scrap metal, added some water and were waiting for results.

Here is the can with the case and the rusty stuff

 

And this is what came out yesterday evening after about 24 hours

 

This was not the result I’ve expected. The rust was not permanent enough. 

I guess the case is made from ahigher grade stainless steel, maybe more chrome in it.

So, what now ?

I had some muriatic acid and a rusty drill

 

Scratched the rust from the drill, applicated it to the case and added some drops of acid

 

Until the surface was dry, I took the case back in the can with the rusty stuff.

 

Added some water and cooked it with a propane burner until all water was vaporized.

 

Now the result was more in the direction I wanted.

 

But still not permanent enough. Now came the time to go the harder way. The case or me

I grabbed my good old propane burner and started the final treatment. I’ve heated the case up with all the rusty and rotten goodies on it, all or nothing..

 

OK, it looks like destroying the case, but it allowes a hard treatment.

I didn’t went over 250 - 300C°.

Fast quenching with cold water dripped area by area made the finish.

 

Enough work for one evening

( Aging of the hands and the dial was also done as a sideline, I will upload the pics later)

This morning at the office I cleaned the case and this is what it looks like now

 

The crownguard is still in the can, it was also cooked with the rusty stuff.

For me is the aged look of the case good enough, not too hard and not too soft.

 

The next step ( done during waiting for corrosion ) aging the dial and hands

Damn, I just wanted to show the bezel aging, now I am nearly done with the whole watch.

Here is the dial that came with the watch. I’ve relumed it with some lume I got from the nice member homecd. I also bleached it a little bit with wet 2000 grit sandpaper.

 

I applicated some chestnut wood staine to the backside

 

But nothing came through to the frontside, so I used a toothpick and applicated the staine to the numbers and indices at the front ( Not really my favourite kind of work )

I also thought it would look nice to have a scratched circle in the diameter of the hourhand.

I cutted a disc in the necessary dimension and made a hole in the middle.

Connected it with the most useful tool, the toothpicker to the dial.

 

Than I had to move the disc with soft pressure in clockwise rotation against the dial.

The dust needs to be wiped away, but the result so, far, was good enough for me.

 

Now I came to the hands, it was also logical for me to use muriatic acid, because the sulphur in it reacts with the brass from the hands

I placed the hands on a bottle cap of my favourite beer ( König Pils ) and added some drops of acid to it

 

After neutralizing the hands with water and cleaning the dial I’ve mounted the dial and hands to the movement

 

So far so good.

Next thing will be the crownguard aging

Now I need the higher domed plexi, compression lugbars ( Dow provides me with them, Thank you mate ) . I have to go outside and have a look at the contamined, sandblastet piece of stainless steel.

 

Today we went into our workshop, my welding supervisor ( indredible welder ) and me.

At first I made a test with 1,6mm welding wire to see if it fits the holes

 

Was ok for one side, the other side with the thread was smaller ( used 1mm wire )

I’ve cutted the wire in small pieces with 2mm extention out of the lugs, that was necessary

for melting it into the holes.

 

Now a view with my welding artist at work,

 

Welding is done and the weld dots came out flat and massive

 

Here are detailed views of the welded lugs

 

Next step is filing the lugs back to the shape they had before, after that I have to drill new holes for the lug bars.

To be continued….

[HeavyKrush 16]

Anyone know what happened with this build?

[codo 0]

Cool story - great result!

[Pihlippe 1,264]

Anyone know what happened with this build?

 

Hmm part 2 is here, if you did'nt find it.....

[decus 0]

Nice...

[Abagnale 0]

yep, definitely!